 |
| Add caption |
Konfigurasi switch
Switch>en
Switch>enable
Switch#conf t
Switch#conf terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname Switch_Server
Switch_Server(config)#int
Switch_Server(config)#interface fa
Switch_Server(config)#interface fastEthernet 0/1
Switch_Server(config-if)#no shutdown
Switch_Server(config-if)#exit
Switch_Server(config)#vlan 2
Switch_Server(config-vlan)#name efri
Switch_Server(config-vlan)#exit
Switch_Server(config)#vlan 3
Switch_Server(config-vlan)#name sulis
Switch_Server(config-vlan)#exit
Switch_Server(config)#vlan 4
Switch_Server(config-vlan)#name agus
Switch_Server(config-vlan)#exit
Switch_Server(config)#vlan 5
Switch_Server(config-vlan)#name jamal
Switch_Server(config-vlan)#exit
Switch_Server(config)#vlan 6
Switch_Server(config-vlan)#name yunus
Switch_Server(config-vlan)#exit
Switch_Server(config)#vlan 7
Switch_Server(config-vlan)#name doni
Switch_Server(config-vlan)#exit
Switch_Server(config)#vlan 8
Switch_Server(config-vlan)#name mario
Switch_Server(config-vlan)#exit
Switch_Server(config)#vlan 9
Switch_Server(config-vlan)#name dika
Switch_Server(config-vlan)#exit
Switch_Server(config)#vlan 10
Switch_Server(config-vlan)#name riko
Switch_Server(config-vlan)#exit
Switch_Server(config)#vlan 11
Switch_Server(config-vlan)#name andry
Switch_Server(config-vlan)#exit
Switch_Server(config)#^Z
Switch_Server#
%SYS-5-CONFIG_I: Configured from console by console
Switch_Server#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Switch_Server#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
2 efri active
3 sulis active
4 agus active
5 jamal active
6 yunus active
7 doni active
8 mario active
9 dika active
10 riko active
11 andry active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
2 enet 100002 1500 - - - - - 0 0
3 enet 100003 1500 - - - - - 0 0
4 enet 100004 1500 - - - - - 0 0
5 enet 100005 1500 - - - - - 0 0
6 enet 100006 1500 - - - - - 0 0
7 enet 100007 1500 - - - - - 0 0
8 enet 100008 1500 - - - - - 0 0
9 enet 100009 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
11 enet 100011 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
Switch_Server#
Switch_Server#
Switch_Server#
Switch_Server#en
Switch_Server#enable
Switch_Server#conf t
Switch_Server#conf terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch_Server(config)#int
Switch_Server(config)#interface fa
Switch_Server(config)#interface fastEthernet 0/1
Switch_Server(config-if)#sw
Switch_Server(config-if)#switchport mo
Switch_Server(config-if)#switchport mode tr
Switch_Server(config-if)#switchport mode trunk
Switch_Server(config-if)#sw
Switch_Server(config-if)#switchport tr
Switch_Server(config-if)#switchport trunk na
Switch_Server(config-if)#switchport trunk native vlan 1
Switch_Server(config-if)#exit
Switch_Server(config)#int
Switch_Server(config)#interface fa
Switch_Server(config)#interface fastEthernet 0/2
Switch_Server(config-if)#sw
Switch_Server(config-if)#switchport mo
Switch_Server(config-if)#switchport mode acc
Switch_Server(config-if)#switchport mode access
Switch_Server(config-if)#sw
Switch_Server(config-if)#switchport acc
Switch_Server(config-if)#switchport access vlan 2
Switch_Server(config-if)#exit
Switch_Server(config)#int
Switch_Server(config)#interface fa
Switch_Server(config)#interface fastEthernet 0/3
Switch_Server(config-if)#sw
Switch_Server(config-if)#switchport mo
Switch_Server(config-if)#switchport mode acc
Switch_Server(config-if)#switchport mode access
Switch_Server(config-if)#sw
Switch_Server(config-if)#switchport acc
Switch_Server(config-if)#switchport access vlan 3
Switch_Server(config-if)#exit
Switch_Server(config)#interface fastEthernet 0/4
Switch_Server(config-if)#switchport mode access
Switch_Server(config-if)#switchport access vlan 4
Switch_Server(config-if)#exit
Switch_Server(config)#interface fastEthernet 0/5
Switch_Server(config-if)#switchport mode access
Switch_Server(config-if)#switchport access vlan 5
Switch_Server(config-if)#exit
Switch_Server(config)#interface fastEthernet 0/6
Switch_Server(config-if)#switchport mode access
Switch_Server(config-if)#switchport access vlan 6
Switch_Server(config-if)#exit
Switch_Server(config)#interface fastEthernet 0/7
Switch_Server(config-if)#switchport mode access
Switch_Server(config-if)#switchport access vlan 7
Switch_Server(config-if)#exit
Switch_Server(config)#interface fastEthernet 0/8
Switch_Server(config-if)#switchport mode access
Switch_Server(config-if)#switchport access vlan 8
Switch_Server(config-if)#exit
Switch_Server(config)#interface fastEthernet 0/9
Switch_Server(config-if)#switchport mode access
Switch_Server(config-if)#switchport access vlan 9
Switch_Server(config-if)#exit
Switch_Server(config)#interface fastEthernet 0/10
Switch_Server(config-if)#switchport mode access
Switch_Server(config-if)#switchport access vlan 10
Switch_Server(config-if)#exit
Switch_Server(config)#interface fastEthernet 0/11
Switch_Server(config-if)#switchport mode access
Switch_Server(config-if)#switchport access vlan 11
Switch_Server(config-if)#exit
Switch_Server(config)#^Z
Switch_Server#
%SYS-5-CONFIG_I: Configured from console by console
Switch_Server#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Switch_Server#
Konfigurasi Router
Router>enable
Router#conf t
Router#conf terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router_Server
Router_Server(config)#interface fa
Router_Server(config)#interface fastEthernet 0/0
Router_Server(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router_Server(config-if)#exit
Router_Server(config)#in
Router_Server(config)#interface fa
Router_Server(config)#interface fastEthernet 0/0.2
%LINK-5-CHANGED: Interface FastEthernet0/0.2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.2, changed state to up
Router_Server(config-subif)#en
Router_Server(config-subif)#encapsulation do
Router_Server(config-subif)#encapsulation dot1Q 2
Router_Server(config-subif)#ip address 192.168.2.1 255.255.255.0
Router_Server(config-subif)#exit
Router_Server(config)#interface fastEthernet 0/0.3
%LINK-5-CHANGED: Interface FastEthernet0/0.3, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.3, changed state to up
Router_Server(config-subif)#encapsulation dot1Q 3
Router_Server(config-subif)#ip address 192.168.3.1 255.255.255.0
Router_Server(config-subif)#exit
Router_Server(config)#interface fastEthernet 0/0.4
%LINK-5-CHANGED: Interface FastEthernet0/0.4, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.4, changed state to up
Router_Server(config-subif)#encapsulation dot1Q 4
Router_Server(config-subif)#ip address 192.168.4.1 255.255.255.0
Router_Server(config-subif)#exit
Router_Server(config)#interface fastEthernet 0/0.5
%LINK-5-CHANGED: Interface FastEthernet0/0.5, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.5, changed state to up
Router_Server(config-subif)#encapsulation dot1Q 5
Router_Server(config-subif)#ip address 192.168.5.1 255.255.255.0
Router_Server(config-subif)#exit
Router_Server(config)#interface fastEthernet 0/0.6
%LINK-5-CHANGED: Interface FastEthernet0/0.6, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.6, changed state to up
Router_Server(config-subif)#encapsulation dot1Q 6
Router_Server(config-subif)#ip address 192.168.6.1 255.255.255.0
Router_Server(config-subif)#exit
Router_Server(config)#interface fastEthernet 0/0.7
%LINK-5-CHANGED: Interface FastEthernet0/0.7, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.7, changed state to up
Router_Server(config-subif)#encapsulation dot1Q 7
Router_Server(config-subif)#ip address 192.168.7.1 255.255.255.0
Router_Server(config-subif)#exit
Router_Server(config)#interface fastEthernet 0/0.8
%LINK-5-CHANGED: Interface FastEthernet0/0.8, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.8, changed state to up
Router_Server(config-subif)#encapsulation dot1Q 8
Router_Server(config-subif)#ip address 192.168.8.1 255.255.255.0
Router_Server(config-subif)#exit
Router_Server(config)#interface fastEthernet 0/0.9
Router_Server(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.9, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.9, changed state to up
Router_Server(config-subif)#encapsulation dot1Q 9
Router_Server(config-subif)#ip address 192.168.9.1 255.255.255.0
Router_Server(config-subif)#exit
Router_Server(config)#interface fastEthernet 0/0.10
Router_Server(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.10, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.10, changed state to up
Router_Server(config-subif)#encapsulation dot1Q 10
Router_Server(config-subif)#ip address 192.168.10.1 255.255.255.0
Router_Server(config-subif)#exit
Router_Server(config)#interface fastEthernet 0/0.11
%LINK-5-CHANGED: Interface FastEthernet0/0.11, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.11, changed state to up
Router_Server(config-subif)#encapsulation dot1Q 11
Router_Server(config-subif)#ip address 192.168.11.1 255.255.255.0
Router_Server(config-subif)#exit
Router_Server(config)#^Z
Router_Server#
%SYS-5-CONFIG_I: Configured from console by console
Router_Server#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router_Server#
Tidak ada komentar:
Posting Komentar